
Knife gate valve · Supplied by BAUTU
Knife Gate Valve — DN50 to DN800, PN10 and ASME Class 150
Knife gate valve for on/off isolation of thick, fibrous and solids-laden media: paper pulp, sewage, coal slurry, ash slurry and slag-water mixtures. The sharp-edged gate cuts through the media as it closes. PN6, PN10, PN16 and ASME Class 150, DN50 to DN800. Larger and non-standard sizes are made to order.
- Supplied by BAUTU, pressure-tested and inspected before shipment
- Material certificate and test report with every shipment
- One supplier for your gate, globe, check and knife gate valves
- Standard sizes ship in 15–20 days
An engineer replies within 24 hours. Send size, PN, material and quantity.
Specifications
Technical Data
| Pressure rating | PN6 / PN10 / PN16 (0.6 / 1.0 / 1.6 MPa) · ASME Class 150 |
| Size range | DN50–DN800 (PN10), larger and non-standard sizes to order · NPS 2″–24″ (Class 150) |
| Rated working pressure | Falls as the size rises: see the table below |
| Body and bonnet | Stainless steel (CF8 / CF3M) · carbon steel (WCB) · grey cast iron |
| Gate | Carbon steel or stainless steel |
| Stem | Stainless steel |
| Seat / sealing | Rubber (standard) · PTFE · stainless steel · carbide alloy |
| Working temperature | ≤ +100 °C |
| Media | Paper pulp, sewage, coal slurry, ash slurry, mortar and slag-water mixtures |
| Operation | Handwheel (rising or non-rising stem), chainwheel, lever, bevel gear, electric or pneumatic actuator |
| Testing | Shell and seat test before shipment; material certificate and test report with every order |
Application
Where It Is Used
For on/off isolation where thick or solids-laden media would jam other valves.
- Pulp and paper lines
- Sewage and wastewater treatment
- Coal slurry and ash slurry lines
- Mortar and slag-water mixtures
Configurations
Representative Configurations
The same valve body with different operators. Chainwheel and lever operation are also available.
Handwheel, rising stem
Manual on/off; the rising stem shows the gate position.
Bevel gear
Manual operation with a gearbox for larger sizes, so less force is needed on the handwheel.
Pneumatic actuator
Double-acting cylinder for automatic open/close from the control system.
Electric actuator
For sites without compressed air or for remote operation.
Real photos
Knife Gate Valves Before Shipment
PNEUMATIC + HANDWHEEL
STAINLESS · PNEUMATIC
PAINTED BODIESConstruction
Parts & Materials
| Part | Material options |
|---|---|
| Body, bonnet | Stainless steel · carbon steel · grey cast iron |
| Gate | Carbon steel · stainless steel |
| Stem | Stainless steel |
| Sealing | Rubber · PTFE · stainless steel · carbide alloy |
Seat options
- Type 1: metal-to-metal
- Type 2: rubber resilient seat (standard)
- Type 3: PTFE resilient seat (reinforced)
- 15° deflector cone
Dimensions
Dimensions (mm)
Unit: mm.
PN10, DN50–DN800
| DN | L | D | D1 | D2 | H | N-M | D0 |
|---|---|---|---|---|---|---|---|
| DN50 | 40 | 160 | 125 | 100 | 285 | 4-M16 | 200 |
| DN65 | 48 | 180 | 145 | 120 | 298 | 4-M16 | 200 |
| DN80 | 50 | 195 | 160 | 135 | 315 | 4-M16 | 220 |
| DN100 | 60 | 215 | 180 | 155 | 365 | 8-M16 | 240 |
| DN125 | 60 | 245 | 210 | 185 | 400 | 8-M16 | 240 |
| DN150 | 62 | 280 | 240 | 210 | 475 | 8-M20 | 280 |
| DN200 | 76 | 335 | 295 | 265 | 540 | 8-M20 | 320 |
| DN250 | 76 | 390 | 350 | 320 | 630 | 12-M20 | 360 |
| DN300 | 80 | 440 | 400 | 368 | 780 | 12-M20 | 400 |
| DN350 | 85 | 500 | 460 | 428 | 885 | 16-M20 | 450 |
| DN400 | 93 | 565 | 515 | 482 | 990 | 16-M22 | 450 |
| DN450 | 93 | 615 | 565 | 532 | 1100 | 20-M22 | 500 |
| DN500 | 130 | 670 | 620 | 585 | 1200 | 20-M22 | 500 |
| DN600 | 130 | 780 | 725 | 685 | 1450 | 20-M27 | 600 |
| DN700 | 135 | 895 | 840 | 800 | 1700 | 24-M27 | 600 |
| DN800 | 140 | 1010 | 950 | 905 | 2000 | 24-M30 | 680 |
ASME Class 150, NPS 2″–24″
| NPS | L | D | D1 | D2 | H | n-Ød | D0 |
|---|---|---|---|---|---|---|---|
| 2″ | 48 | 152 | 120.5 | 92.1 | 285 | 4-18 | 200 |
| 2½″ | 48 | 178 | 139.5 | 110.5 | 298 | 4-19 | 200 |
| 3″ | 50 | 191 | 152.5 | 127 | 315 | 4-19 | 220 |
| 4″ | 60 | 229 | 190.5 | 157.2 | 365 | 8-19 | 240 |
| 5″ | 60 | 254 | 216 | 185.7 | 400 | 8-22 | 240 |
| 6″ | 62 | 279 | 241.5 | 216 | 475 | 8-22 | 280 |
| 8″ | 76 | 343 | 298.5 | 270 | 540 | 8-22 | 320 |
| 10″ | 76 | 406 | 362 | 324 | 630 | 12-25 | 360 |
| 12″ | 80 | 483 | 432 | 381 | 780 | 12-25 | 400 |
| 14″ | 85 | 533 | 476 | 413 | 885 | 12-29 | 450 |
| 16″ | 93 | 597 | 539.5 | 470 | 990 | 16-29 | 450 |
| 18″ | 93 | 635 | 578 | 533 | 1100 | 16-32 | 500 |
| 20″ | 130 | 699 | 635 | 584 | 1200 | 20-32 | 500 |
| 24″ | 130 | 813 | 749.5 | 692 | 1450 | 20-35 | 600 |
Larger and non-standard sizes are made to order — send us your size and pressure.
L face-to-face · D flange outside diameter · D1 bolt circle diameter · D2 sealing face diameter · H height · N-M number and thread size of tapped bolt holes · n-Ød number and diameter of bolt holes · D0 handwheel diameter · — not listed.
Pressure rating
Rated Working Pressure by Size
| DN | Rated pressure (bar) |
|---|---|
| DN50 | 10 |
| DN65 | 10 |
| DN80 | 10 |
| DN100 | 10 |
| DN125 | 10 |
| DN150 | 8 |
| DN200 | 7 |
| DN250 | 5 |
| DN300 | 5 |
| DN350 | 4 |
| DN400 | 4 |
| DN450 | 3 |
| DN500 | 3 |
| DN600 | 3 |
From our catalogue. Larger valves are rated for a lower working pressure.
Testing
Test Pressures
| Nominal pressure | Shell test | Seat test |
|---|---|---|
| 0.6 MPa | 0.9 MPa | 0.66 MPa |
| 1.0 MPa | 1.5 MPa | 1.1 MPa |
| 1.6 MPa | 2.4 MPa | 1.8 MPa |
Shell and seat test pressures. The test report with the actual results ships with the valves.
Options
Operation
- Handwheel, rising stem
- Handwheel, non-rising stem
- Chainwheel
- Lever
- Bevel gear
- Electric actuator
- Pneumatic actuator (double-acting)
Send us these 7 details for a fast quote
- Size (DN or NPS)
- Pressure (PN6 / 10 / 16 or Class 150)
- Body material
- Seat (rubber, PTFE or metal)
- Operation (handwheel, gear, electric or pneumatic)
- Media, solids content and temperature
- Quantity and destination port
FAQ
Frequently Asked Questions
What is a knife gate valve used for?
On/off isolation of thick, fibrous or solids-laden media such as paper pulp, sewage, coal slurry, ash slurry and slag-water mixtures. The sharp-edged gate cuts through the media as it closes.
What pressure ratings are available?
PN6, PN10 and PN16 (0.6, 1.0 and 1.6 MPa) and ASME Class 150. The allowed working pressure falls as the size rises, from 10 bar at DN50–DN125 to 3 bar at DN450–DN600; see the pressure table on this page.
Which seat should I choose?
The Type 2 rubber resilient seat is standard. A Type 3 PTFE resilient seat (reinforced), a Type 1 metal-to-metal seat and a 15° deflector cone are also available. Tell us the media, solids content and temperature and we recommend the seat.
How can the valve be operated?
By handwheel (rising or non-rising stem), chainwheel, lever or bevel gear, or with an electric or double-acting pneumatic actuator.
What temperature can it handle?
Up to +100 °C.
What documents ship with the valve?
A material certificate and a test report with the shell and seat test results ship with every order. Third-party inspection (e.g. SGS or BV) is welcome, arranged and paid for by the buyer.
What is the lead time?
Standard sizes ship in 15–20 days. Special sizes, materials or actuators may take longer; we confirm the date with your quote.
Need a Quote for This Valve?
Send size, PN, body material and quantity. An engineer replies within 24 hours.




